Clone Troopers




  • ARC Null Class, Clone Trooper (realistic)

    ARC Null Class, Clone Trooper (realistic)

    CHARACTER DESCRIPTION Numbering only six, the Null-class Advanced Recon Commandos were the first clones of Jango Fett created by the Kaminoan cloners, and the prototypes for the Grand Army of the Republic. They were deemed a failure by the Kaminoans and were not put into mass-production. However, Mandalorian mercenary Kal Skirata saved them from termination by the Kaminoans and later adopted all of them. All of the Nulls were named after Mandalorian warriors. (Source: Wookiepedia) REQUIRED ITEMS NOTE: This clone wears Phase I (Episode II) armor with additional paint and accessories. Only those additional items are listed here. 1. Helmet Colored command stripe around visor and down center of dome (Yellow=Commander / Red=Captain / Blue=Lieutenant / Moss Green=Sergeant) Fett-style Range Finder on right side of helmet. Mounted in the ear, not to the outside. Stalk should be metal colored. Range finder should be black. 2. Armor  Chest Four command dots lined on the left breast. (Red=Captain… Blue=Lieutenant… Moss Green=Sergeant). Dots are approximately .5 to .75 inches in diameter Shoulders Rank stripe down the center (2) Upper Arms Rank stripe on the outside of the bicep, located slightly more toward the front (2) Elbows Rank stripe on outer half of elbow plate (2) Forearms Raised left forearm includes metallic dart, 5 square yellow buttons on outer area and two buttons on inner area of forearm Rank stripe on upper/outside (2) Handplates Entire plate painted with rank color  3. Pauldron Episode III style One large shoulder plate approximately the width of the helmet and painted with matching rank color  One black smaller shoulder plate approximately the same width as the distance from the neck and outer line of the armor at the shoulder  Mantle (or base) should be black 4. Kama Charcoal grey and rectangular shaped with 4 inch “V” cut in bottom/center Matching rank color trim, 1 inch wide Optional 1. Pistols and Holsters One holster on each hip, hanging from the belt ARC or DC-17 pistols acceptable 2. Large Boba Fett-style belt pouches 2 pouches or boxes hanging from opposite sides of belt at hips Pouches/boxes may be soft or rigid 3. Right forearm 4 square yellow buttons Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    ARC, Standard Class, Clone Trooper

    ARC, Standard Class, Clone Trooper

    CHARACTER DESCRIPTION Advanced Recon Commandos, also known as Advanced Recon Clone troopers or simply ARC troopers—were an elite variant of clone trooper in the Grand Army of the Republic during the Clone Wars. Although less numerous than the other clones, they were also among the most skilled soldiers in the galaxy.   (Source: Wookiepedia) REQUIRED ITEMS NOTE: This clone wears Phase I (Episode II) armor with additional paint and accessories. Only those additional items are listed here. 1. Helmet Colored command stripe around visor and down center of dome (Yellow=Commander / Red=Captain / Blue=Lieutenant / Moss Green=Sergeant) Fett-style Range Finder on right side of helmet. Mounted in the ear, not to the outside. Stalk should be metal colored. Range finder should be black. 2. Armor  Chest Shoulders Rank stripe down the center (2) Upper Arms Rank stripe on the outside of the bicep, located slightly more toward the front (2) Elbows Rank stripe on outer half of elbow plate (2) Forearms Raised left forearm includes metallic dart, 5 square yellow buttons on outer area and two buttons on inner area of forearm Rank stripe on upper/outside (2) Handplates Entire plate painted with rank color  3. Pauldron ARC style pauldron Black with 4 panels over left shoulder painted to match rank color 4. Kama Charcoal grey Front/bottom corners should extend to bottom of knee plates 2 triangular detail pieces at front/top Matching rank color trim, 1 inch wide Optional 1. Pistols and Holsters (Red ARC only) One holster on each hip, hanging from the belt Option A – 2 DC-17 Pistols Option B – 2 ARC Trooper pistols 2. Pauldron Option (Red ARC only) 2 or 3 black leather or leather-like ammo pouches hang from pauldron on right breast 3. Large Boba Fett-style belt pouches (Blue ARC only) 2 pouches or boxes hanging from opposite sides of belt at hips Pouches/boxes may be soft or rigid 4. Kama Option 4 inch “V” cut in bottom/center Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    Clone Trooper Soldier, The Clone Wars (animated style)

    Clone Trooper Soldier, The Clone Wars (animated style)

    CHARACTER DESCRIPTION Clone troopers were an army of identical, genetically-modified clones, created to serve in the Grand Army of the Republic during the full-scale intergalactic conflict that came to be known as the Clone Wars. Grown at an accelerated rate and raised in the laboratories and facilities of Kamino, the clone troopers were trained throughout the first ten years of their lives to become one of the most efficient military forces in galactic history. Bred for the sole purpose of combat, the clones were indoctrinated with unwavering obedience to the Galactic Republic and—more specifically—their Commander-in-Chief, the Supreme Chancellor. For roughly three years, the clone troopers fought to defend Republic sovereignty against the Separatist rebellion. Throughout the conflict, the members of the Jedi Order served as commanders and generals of the Grand Army and, thus, they served alongside their clone soldiers on many occasions. But the covert Sith plot to seize control of the galaxy, masterminded by the Sith Lord Darth Sidious, effectively caused the clones to betray and destroy the Republic that they were sworn to protect with their lives. Sidious, in his public guise as Chancellor Palpatine, issued Order 66 to the clone troopers on the eve of the Clone Wars’ end. (Source: Star Wars Wiki) REQUIRED ITEMS Black Undersuit One or two piece black undersuit. Commonly used components include sports compression wear, warm-up suits, dance unitards, or diveskins. Undersuit must be smooth in appearance or with vertical ribbing with no labels or logos visible once the armor is on. Black Gloves Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. Neck Seal Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable. Helmet The Clone Wars animated style clone helmet – Fanmade bucket. Some “name brand” helmets may be unacceptable. Visor – Black visor covers entire “T” shape and frown Helmet Fin on dome 4 black vents on each side of helmet Primer grey stripe around back of dome. NOTE: Episode II style helmets are not acceptable Armor Chest – Chest and back plate should match together at the sides with no gap, just a seam line. Back – Chest and back plate should match together at the sides with no gap, just a seam line. Shoulders Shoulder Straps – Correct shape with ridges. Upper Arms – Front/back pieces are seamless. Forearms- Inner seam/clamshell design allowed. Hand plates AB plate Kidney/Lower Back Piece Butt Plate Cod piece Upper thighs – Front/back pieces are seamless. Lower Legs Compad on left forearm Clone Trooper boots White shoes with white soles Strap across top of foot with circular detail pieces at each end Proper toe detail No laces or logos Belt The Clone Wars style belt Segmented (or segmented-look) belt One large belt box, opposite each other, on hips Thermal detonator centered on rear of belt Optional Elements listed as acceptable here may not be traditionally associated with a costume, but are not so unreasonable as to detract from it. Please keep in mind that the following items may not be...

    read more

    Clone Trooper, 327th Star Corps

    Clone Trooper, 327th Star Corps

    CHARACTER DESCRIPTION The troops of the 327th Star Corps were distinguished by striped yellow markings running the length of their armor and, as a result of Clone Marshal Commander Bly’s ARC training, his troopers were allowed to don kamas and command pauldrons. One unit within the 327th was K Company. (Source: Wookiepedia) REQUIRED ITEMS NOTE: This clone wears Phase II (Episode III) armor with additional paint and accessories. Only those additional items are listed here. Helmet Marigold color stripe down the center, starting in the rear above the grey band and tapering slightly toward the chin.  Armor Chest – Marigold stripe down the center Shoulders – Marigold stripe down the center Upper Arms – Marigold stripe on the outside of the bicep, located slightly more toward the front Forearms – Marigold stripe on upper/outside Handplates – Marigold stripes down center Knees – Marigold stripes down center Belt 2 Marigold stripes on the center-most raised rectangular details Boots 2 Marigold stripes. One on the boot strap and one just below the strap Pauldron Episode III style pauldron One large shoulder plate approximately the width of the helmet and painted in a brown/sienna color One black smaller shoulder plate approximately the same width as the distance from the neck and outer line of the armor at the shoulder Mantle (or base) should be black Note: The 327th Star Corps clone may wear the pauldron to the left or right. Ammo Boxes 3 ammo boxes are attached to a dark grey strap that is attached to the pauldron (on the opposite side of the large shoulder plate) and runs down to the belt. Outer area of boxes is white. Inner portion is raw sienna with a black square located towards the top. 2 smaller ammo boxes are attached to the bicep (opposite the large shoulder plate) on a light grey strap. One box is located on the front of the bicep and the other is located on the outside. Outer area of boxes is white. Inner portion is raw sienna. Kama Brown and rectangular shaped with 4 inch “V” cut in bottom/center Straps are attached to kama buckle with clips and are stitched to the inside of the kama Kama buckle Buckle is located under the front/center of the belt. Kama straps are attached to the buckle with clips Pistols and Holsters One holster on each hip, hanging from the belt 2 DC-17 Pistols (see photo reference) Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    Clone Trooper, Galactic Marine

    Clone Trooper, Galactic Marine

    CHARACTER DESCRIPTION The Galactic Marines, originally known as the 21st Nova Corps of the 4th Sector Army, was an elite unit that was created as the Grand Army of the Republic diversified during the Clone Wars. Following the formation of the Galactic Empire in 19 BBY, they became known as Imperial Galactic Marines. Source: Wookiepedia REQUIRED ITEMS 1. Undersuit The trousers are a grey and have a cod insert on the front. One rectangular cargo pocket with flap centered on the front of each thigh. Upper portion of undersuit may be black or dark grey  2. Black Gloves Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin.  3. Helmet GM Clone Style Helmet – Fanmade helmet Black or Green Visor -Welding Shield above grade 5. Lenses may be flat or bubble, either is acceptable White Cowl  4. Armor Chest – Specific shape to the GM to include 3 greeblies on front/lower area of chest plate Back – Specific shape/size to match the GM chest or regular movie style clone armor Shoulders – Specific shape to the GM, each shoulder is different shape Upper Arms – Seamless regular clone armor Forearms – Seamless regular clone armor Elbows – 2 detail slots on the outside area of both elbow pieces regular clone armor Elbow – Straps regular clone elbow straps, white in color Handplates – Regular clone armor Knees – Specific to the GM Knee Straps – Regular clone knee straps, white in color Lower shin/calf – Specific to a GM to include 2 sets of white straps with clip greeblies each Boot Armor Plates Note: All armor should be weathered. Black wash is an example of an acceptable weathering technique. Exposed rivets are not acceptable. 5. Belt Belt has 2 large and 2 small pouches accompanied by 2 buckle-looking greeblies on the front and a kama buckle in the front/center Top of belt should be mounted just below the chest/back plates with little or no gap visible  6. Boots Must be white leather or leather-like with the sole pattern to match as closely as possible to the movie costume. Most identifiable features include a high arch pattern on the inside of the sole, four profile “swoops” between the sole and leather. Snaps on both side of heel upper to secure the boot armor is suggested.  7. Kama Color should closely match that of armor Length starts just under belt down to top of shin armor / Width is larger at the top than the bottom 4″ split at back/bottom/center 2 white straps connect to belt via kama buckle  8. Ammo Boxes 3 white ammo boxes and one grey clip greeblie attached to a grey strap on right side of chest 2 smaller white ammo boxes are attached to the right bicep on a white strap.  9. Backpack Consists of a main shell and two side shells over a base mounted to the back armor. Also has a detonator type attachment underneath with 4 pouches below that and assorted greebles to the side of the backpack.  10. Pauldron Recommended These costume elements are in addition to the required list of costume parts and are optional. This list provides costuming options that increase the level of accuracy of the...

    read more

    Clone Trooper, Episode III Soldier (Phase II)

    Clone Trooper, Episode III Soldier (Phase II)

    CHARACTER DESCRIPTION The clone troopers of the Grand Army of the Republic are soldiers in the Star Wars universe, cloned from Jango Fett, a Mandalorian bounty hunter. They first appeared in Star Wars Episode II: Attack of the Clones, and returned in Star Wars Episode III: Revenge of the Sith where they were played primarily by Temuera Morrison. In the two Clone Wars animated TV shows, they are voiced by Andre Sogliuzzo and Dee Bradley Baker. Clone troopers comprised the bulk of the Army of the Republic during the Clone Wars. They are depicted as the main part of the armed forces of the Galactic Republic in its final years, becoming one of the largest armies ever assembled, only surpassed by the Separatist Droid Army. Nearing the end of the clone wars, they were ordered to slay the Jedi. This famous Jedi purge was known as ‘Order 66’. After the Clone Wars, they served as the nucleus for the armed forces of the Galactic Empire, eventually becoming the Imperial Stormtroopers. Source: Wikipedia REQUIRED ITEMS 1. Black Undersuit One or two piece black undersuit. Commonly used components include sports comression wear, warm-up suits, dance unitards, or diveskins. Undersuit must be smooth in appearance or with vertical ribbing with no labels or logos visible once the armor is on. 2. Black Gloves Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. 3. Neck Seal Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable. 4. Helmet Episode III (Phase II) style Clone Helmet – Fanmade helmet. Some “name brand” helmets may be unacceptable. Visor – mirrored/chrome or black visor 9 blue or black vent stripes on each side of cheek tubes Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown. Grey stripe around back of dome. 5. Armor  Chest – Two detail slots on right breast. Chest and back plate should match together at the sides with no gap, just a seam line. Back – Chest and back plate should match together at the sides with no gap, just a seam line. Shoulders Shoulder Straps – Correct shape with ridges. Upper Arms – Front/back pieces are seamless. Forearms – Front/back pieces are seamless. Elbows – Two detail slots on the outside area of both elbow pieces. Elbow Straps Handplates AB plate – Four 1/4″ diameter holes per side on indents of ab plate, eight holes total. Kidney/Lower Back Piece Butt Plate Cod piece Upper thighs – Front/back pieces are seamless. Knees – Detail clip with slots on each side of both knees. Knee Straps – Correct shape with center portion of both knee straps raised and primer grey. Lower Legs – Front/back pieces are seamless on outside seam as minimum requirement. Compad on Right forearm Note: – All armor should be matte white or satin white (NO GLOSS). – Armor does not have to be weathered. If weathering is preferred, black wash is an example of an acceptable weathering technique. – No obvious, visible rivets. 6. Belt...

    read more

    Clone Trooper, Episode II Soldier (Phase I)

    Clone Trooper, Episode II Soldier (Phase I)

    CHARACTER DESCRIPTION The clone troopers of the Grand Army of the Republic are soldiers in the Star Wars universe, cloned from Jango Fett, a Mandalorian bounty hunter. They first appeared in Star Wars Episode II: Attack of the Clones, and returned in Star Wars Episode III: Revenge of the Sith where they were played primarily by Temuera Morrison. In the two Clone Wars animated TV shows, they are voiced by Andre Sogliuzzo and Dee Bradley Baker. Clone troopers comprised the bulk of the Army of the Republic during the Clone Wars. They are depicted as the main part of the armed forces of the Galactic Republic in its final years, becoming one of the largest armies ever assembled, only surpassed by the Separatist Droid Army. Nearing the end of the clone wars, they were ordered to slay the Jedi. This famous Jedi purge was known as ‘Order 66’. After the Clone Wars, they served as the nucleus for the armed forces of the Galactic Empire, eventually becoming the Imperial Stormtroopers. Source: Wikipedia REQUIRED ITEMS 1. Black Undersuit One or two piece black undersuit. Commonly used components include sports comression wear, warm-up suits, dance unitards, or diveskins. Undersuit must be smooth in appearance or with vertical ribbing with no labels or logos visible once the armor is on. 2. Black Gloves Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. 3. Neck Seal Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable. 4. Helmet Episode 2 style Clone Helmet – Fanmade bucket. Some “name brand” helmets may be unacceptable. Visor – Mirrored/Chrome or Black Visor Helmet Fin on dome Rear fin needs a brake light cover installed. 6 Primer Grey Vents on each side of helmet cheeks Helmet frown is charcoal grey in color. Wire or plastic mesh is utilized inside the helmet to cover the open pieces of the frown. Primer grey stripe around back of dome. Ear holes may be painted light grey or remain white. 5. Armor  Chest – Two detail slots on right breast. Chest and back plate should match together at the sides with no gap, just a seam line. Back – Chest and back plate should match together at the sides with no gap, just a seam line. Shoulders Shoulder Straps – Correct shape with ridges. Upper Arms – Front/back pieces are seamless. Forearms – Front/back pieces are seamless. Elbows – Two detail slots on the outside area of both elbow pieces. Elbow Straps Handplates AB plate – Four 1/4″ diameter holes per side on indents of ab plate, eight holes total. Kidney/Lower Back Piece Butt Plate Cod piece Upper thighs – Front/back pieces are seamless. Knees – Detail clip with slots on each side of both knees. Knee Straps – Correct shape with center portion of both knee straps raised and primer grey. Lower Legs – Front/back pieces are seamless on outside seam as minimum requirement. Compad on Right forearm Note: – All armor should be matte white or satin white (NO GLOSS). – Armor does not have to...

    read more

    Clone Pilots (Episode III)

    Clone Pilots (Episode III)

    CHARACTER DESCRIPTION Clone trooper pilots were special clone troopers bred in the Kamino cloning centers for the purpose of piloting craft of the Grand Army of the Republic and the early Galactic Empire. They first appeared at the Battle of Geonosis,where they flew LAAT/i and LAAT/c gunships. Pilots also operated CR20 and CR25 troop carriers. In addition, they flew starfighters such as the V-19 Torrent, ARC-170, and Alpha-3 Nimbus-class V-wing. The pilots who flew capital ships wore a special type of armor instead of the regular one, seen in the First Battle of Mon Calamari, during the Clone Wars. Pilots also knew how to operate all military land vehicles such as the AT-TEs. Source: Wookiepedia REQUIRED ITEMS 1. Grey flightsuit with Old Republic patches   2. White hard chest armour front and back connected with black nylon webbing, and 2 shoulder plates   3. Chest box   4. Grey hoses from chest box to helmet   5. White ARC-170 helmet   6. White boots   7. White gauntlet type gloves   8. White belt  COSTUME RESOURCES CloneTroopers.Net PLEASE NOTE: The costume standards are a guide, yet are not an all inclusive outline of required elements. The judges will be looking for quality of workmanship, accurate execution and use of materials in addition to these general standards check lists. If you have a question about fabrics, colours, and parts choices for your build please contact the LCJs for your category about parts/materials you are considering before you start your build. (LCJ listing here) Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    Clone Pilots (Episode II)

    Clone Pilots (Episode II)

    CHARACTER DESCRIPTION Clone trooper pilots were special clone troopers bred in the Kamino cloning centers for the purpose of piloting craft of the Grand Army of the Republic and the early Galactic Empire. They first appeared at the Battle of Geonosis,where they flew LAAT/i and LAAT/c gunships. Pilots also operated CR20 and CR25 troop carriers. In addition, they flew starfighters such as the V-19 Torrent, ARC-170, and Alpha-3 Nimbus-class V-wing. The pilots who flew capital ships wore a special type of armor instead of the regular one, seen in the First Battle of Mon Calamari, during the Clone Wars. Pilots also knew how to operate all military land vehicles such as the AT-TEs. Source: Wookiepedia REQUIRED ITEMS 1. Complete clone armour 2. Modified clone helmet with chest box attached to helmet by 2 hoses 3. Yellow detail paint 4. Black undersuit with high collar or neck seal COSTUME RESOURCES CloneTroopers.Net PLEASE NOTE: The costume standards are a guide, yet are not an all inclusive outline of required elements. The judges will be looking for quality of workmanship, accurate execution and use of materials in addition to these general standards check lists. If you have a question about fabrics, colours, and parts choices for your build please contact the LCJs for your category about parts/materials you are considering before you start your build. (LCJ listing here) Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    Clone Officer

    Clone Officer

    CHARACTER DESCRIPTION Clone naval officers also known as clone navigators were clone troopers specifically trained in technical and tactical aspects of naval command. Kaminoan scientists speculated that clones’ aptitude for space combat came from Jango Fett’s understanding of dogfight tactics, but even amongst his clones some had proved themselves capable of understanding and executing naval strategy to a greater degree than their brothers. Those clones received special naval training and many of them eventually became officers in the Republic Navy, although most of them were lower-tier commanders and aides to superior non-clone officers. Some of those officers believed that despite their training the clones were not suited for a role of an officer, which sometimes led to rising tensions aboard Galactic Republic ships. Although Grand Army of the Republic soldiers such as Rom Mohc had a high opinion of clones and relished working with them, others decided to avoid following Mohc’s kindness. As a result, these naval officers had tense relationships with officers. Source: Wookiepedia REQUIRED ITEMS Gray long sleeve jacket (needs to extend below the waist down to hips, and be made from a good quality suiting material.) Epaulets on both shoulders Mandarin-style Collar with closure on the right side “S” seam on front of jacket (extending from bottom on L side; rising to mid chest and curving 90 degrees to the R; across chest then curving 90 degrees to vertical; then rising to the L shoulder epaulet) 2 stripes on jacket cuff Black belt w/ rectangle silver buckle. Rank insignia on L breast Pants in matching fabric Black boots rising to just below the knee Short clone hair style only (long hair will not be accepted) RECOMMENDED Dark piping to outline the “S” seam on the jacket front Split skirt on back of jacket  Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    Clone Commander, Deviss

    Clone Commander, Deviss

    CHARACTER DESCRIPTION CT-65/91-6210, also known as “Deviss,” was a clone trooper captain who led K Company, a unit within Clone Commander Bly’s 327th Star Corps. In 22 BBY, Deviss served in the the first battle of the Clone Wars on the Outer Rim planet Geonosis. During the battle, Deviss risked his life to protect two injured soldiers from Confederate spider droids and received a medal after being rescued from behind enemy lines by Republic troops. He went on to fight in the Battle of Altyr V, after which he was promoted to commander for his actions. He also participated in a battle on Cato Neimoidia. In 19 BBY, Deviss was dispatched to support Jedi General Nem Bees on Orto. During a battle on the planet, the Commander received Order 66—which called for all clone troopers to execute their Jedi officers—and personally shot down Bees on the front lines. Source: Wookiepedia REQUIRED ITEMS NOTE: This clone wears Phase II (Episode III) armor with additional paint and accessories. Only those additional items are listed here. 1. Helmet Binoc set mounted to the helmet Red stripe down the center, starting in the rear above the grey band and tapering slightly toward the chin (mohawk is left white) 2. Armor Chest – Red stripe down the center Shoulders – Red stripe down the center Upper Arms – Red stripe on the outside of the bicep, located slightly more toward the front Forearms – Red stripe on upper/outside, Shape of compad is painted on left forearm Handplates – Red stripes down center Knees – Red stripes down center 3. Belt 2 red stripes on the center-most raised rectangular details 4. Boots 2 Red stripes. One on the boot strap and one just below the strap 5. Pauldron Episode III style pauldron One large shoulder plate approximately the width of the helmet and painted red One black smaller shoulder plate approximately the same width as the distance from the neck and outer line of the armor at the shoulder Mantle (or base) should be black 6. Ammo Boxes 3 ammo boxes are attached to a grey strap that is attached to the pauldron (on the opposite side of the large shoulder plate) and runs down to the belt. Outer area of boxes is white. Inner portion is raw sienna with a black square located towards the top. 2 smaller ammo boxes are attached to the bicep (opposite the large shoulder plate) on a grey strap. One box is located on the front of the bicep and the other is located on the outside. Outer area of boxes is white. Inner portion is raw sienna. 7. Kama Taupe and rectangular shaped with 4 inch “V” cut in bottom/center Straps are white and attached to kama buckle with clips and are stitched to the inside of the kama 8. Kama buckle Buckle is located under the front/center of the belt. Kama straps are attached to the buckle with clips 9. Pistols and Holsters One holster on each hip, hanging from the belt 2 DC-17 Pistols (see photo reference) Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    Clone Commander, Bly

    Clone Commander, Bly

    CHARACTER DESCRIPTION CC-5052 was a clone marshal commander who served both the Galactic Republic and the Galactic Empire that followed. A clone of Jango Fett, CC-5052 was bred on Kamino, where he was trained as an Advanced Recon Commando by Alpha-17. Alpha-17 also gave CC-5052 the name “Bly,” which the clone commander himself adopted. Assigned to the 327th Star Corps, Bly worked with Jedi General Aayla Secura throughout the Clone Wars. Serving in campaigns on planets such as Quell, Maridun, Alzoc III, Florrum, and New Holstice, Bly worked with Secura to personally extract a valuable Scientific Instrument Package from Honoghr. During the mission, Bly encountered renegade Jedi Quinlan Vos, whom he deeply mistrusted. Shortly after the Honoghr mission, Bly and Secura served alongside the reformed Vos in the Siege of Saleucami. Source: Wookiepedia REQUIRED ITEMS NOTE: This clone wears Phase II (Episode III) armor with additional paint and accessories. Only those additional items are listed here. 1. Helmet Binoc set mounted to the helmet Yellow mohawk and lower portion of helmet Sandy brown stripe down the center, starting in the rear above the grey band and tapering slightly toward the chin 2. Armor  Chest – Sandy brown stripe down the center  Shoulders – Sandy brown stripe down the center  Upper Arms – Sandy brown stripe on the outside of the bicep, located slightly more toward the front  Forearms – Sandy brown stripe on upper/outside, shape of compad is left white on left forearm  Handplates – Sandy brown stripe down center  Thighs – Yellow with sandy brown stripe down front/center  Knees – Sandy brown stripes down center 3. Belt Large/front boxes and belt in between are painted yellow 4. Boots 2 Yellow stripes. One on the boot strap and one just below the strap 5. Pauldron Episode III style pauldron One large shoulder plate approximately the width of the helmet and painted in a brown/sienna color One black smaller shoulder plate approximately the same width as the distance from the neck and outer line of the armor at the shoulder Mantle (or base) should be black 6. Ammo Boxes 3 ammo boxes are attached to a grey strap that is attached to the pauldron (on the opposite side of the large shoulder plate) and runs down to the belt. Outer area of boxes is white. Inner portion is raw sienna with a black square located towards the top. 2 smaller ammo boxes are attached to the bicep (opposite the large shoulder plate) on a grey strap. One box is located on the front of the bicep and the other is located on the outside. Outer area of boxes is white. Inner portion is raw sienna. 7. Kama Taupe and rectangular shaped with 4 inch “V” cut in bottom/center Straps are white and attached to kama buckle with clips and are stitched to the inside of the kama 8. Kama buckle Buckle is located under the front/center of the belt. Kama straps are attached to the buckle with clips 9. Pistols and Holsters One holster on each hip, hanging from the belt 2 DC-17 Pistols (see photo reference)   Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    Clone Commander, Bly (Animated)

    Clone Commander, Bly (Animated)

    CHARACTER DESCRIPTION CC-5052 was a clone marshal commander who served both the Galactic Republic and the Galactic Empire that followed. A clone of Jango Fett, CC-5052 was bred on Kamino, where he was trained as an Advanced Recon Commando by Alpha-17. Alpha-17 also gave CC-5052 the name “Bly,” which the clone commander himself adopted. Assigned to the 327th Star Corps, Bly worked with Jedi General Aayla Secura throughout the Clone Wars. Serving in campaigns on planets such as Quell, Maridun, Alzoc III, Florrum, and New Holstice, Bly worked with Secura to personally extract a valuable Scientific Instrument Package from Honoghr. During the mission, Bly encountered renegade Jedi Quinlan Vos, whom he deeply mistrusted. Shortly after the Honoghr mission, Bly and Secura served alongside the reformed Vos in the Siege of Saleucami. Source: Wookipedia REQUIRED ITEMS 1. Black Undersuit One or two piece black undersuit. Commonly used components include sports compression wear, warm-up suits, dance unitards, or diveskins. Undersuit must be smooth in appearance or with vertical ribbing with no labels or logos visible once the armor is on. 2. Black Gloves Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. 3. Neck Seal Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable. 4. Helmet The Clone Wars animated style clone helmet – Fanmade bucket. Some “name brand” helmets may be unacceptable. Helmet Fin on dome painted Golden Yellow. Golden Yellow stripe down center, tapering slightly toward the “chin” and upwards just past the helmet fin. Primer grey rear detail Macro binoculars (animated style) mounted to “ear” area. Smoked/black visor over entire opening on face of helmet 4 black vents on each side of helmet. NOTE: Episode II style helmets are not acceptable 5. Armor  Chest – Chest and back plate should match together at the sides with no gap, just a seam line. Golden Yellow strip down center.  Back – Chest and back plate should match together at the sides with no gap, just a seam line.  Shoulders – Golden Yellow stripes centered on shoulders  Shoulder Straps – Correct shape with ridges. Golden Yellow stripes  Upper Arms – Front/back pieces are seamless. Golden Yellow stripes  Forearms – Front/back pieces are seamless. Golden Yellow stripes on Forearm  Handplates – Golden Yellow stripes  AB plate  Kidney/Lower Back Piece  Butt Plate  Cod piece  Upper thighs – Front/back pieces are seamless. Golden Yellow in color w/ Sandy Brown strip down the center  Lower Legs – Sandy Brown stripes on knees  Compad on left forearm 6. Clone Trooper boots White shoes with white soles Strap across top of foot with circular detail pieces at each end Proper toe detail No laces or logos 2 Golden Yellow stripes. One on the boot strap (but not the circular detail) and one just below the strap 7. Belt The Clone Wars style belt Segmented (or segmented-look) belt One large belt box, opposite each other, on hips Thermal detonator centered on rear of belt 8. Kama Heavy weight fabric, leather, or leather-like material, dark brown, with gold trim Length should be to the bottom of the...

    read more

    Captain Rex (realistic)

    Captain Rex (realistic)

    CHARACTER DESCRIPTION CT-7567, nicknamed “Rex,” was a clone trooper captain during the Clone Wars, the galaxy-wide conflict between the Galactic Republic and the Confederacy of Independent Systems. Rex was in command of Torrent Company, a unit of the famed 501st Legion in the Grand Army of the Republic. Rex served under Jedi General Anakin Skywalker, and was a freethinking, tough, and aggressive trooper. Though loyal and committed to his duty and to his fellow clones, Rex proved capable of questioning his superiors and, under extreme circumstances, outright disobeying orders if he believed them to be wrong. Rex displayed a strong working relationship and a degree of friendship with Commander Cody. Rex was one of the many clones of bounty hunter Jango Fett, bred on Kamino by the Galactic Republic to fight in the Republic’s clone army. The soldiers were bred to fight against the separatist planetary and sectorial governments seeking to leave the Republic, known as Confederacy of Independent Systems, in the coming war. Rex served on Geonosis alongside Denal and was promoted to the rank of captain, he was also in command of Torrent Company, a unit in the famous 501st Legion. Rex was assigned to Jedi General Anakin Skywalker, and would participate in many missions alongside the Jedi Knight, including Jabiim. Rex also developed a friendship with fellow clone trooper Commander Cody. Source: Wookiepedia REQUIRED ITEMS NOTE: This clone wears Phase I (Episode II) armor with additional paint and accessories. Only additional additonal features are listed here. 1. Helmet Blue eyes and triangles on forehead Blue visor trim, rear detail, and 2 vertical ribs back of helmet Yellow “kill stripes”, 4 on each side of the forehead Rangefinder (Boba/Jango Fett style) mounted on right/outsdie of helmet and painted white Black or charcoal grey frown Smoked/black visor (mirrored acceptable) NOTE: Rubies helmet is not acceptable 2. Armor  Shoulders – Blue stripe down the center  Upper Arms – Blue stripe on the outside of the bicep, located slightly more toward the front  Elbows – Blue stripe centered on elbow plate  Forearms – Rank stripe on upper/outside  Hand Plates – Rank stripes down center  Knees -Blue stripe down center 3. Pauldron (black, grey, and blue) Similar to Episode III style Shoulder plate is no longer than helmet is wide Mantle plates painted grey Left shoulder plate details painted blue 4. Kama Black with blue trim Length should be to the bottom of the thigh armor Split up the back all the way to the belt Spacing in the front should place the edges of the kama at roughly the outside corners of the bottom of the codpiece 5. Pistols and Holsters One holster on each hip, hanging from the belt 2 DC-17 Pistols OPTIONAL Weathering – HIGHLY RECOMMENDED – Color should be heavy on the greys, with little/no browns Other clone weapons – Rex is shown with just about all of the accepted Clone weapons at some point in the movie/series Jango Fett “Arena” style jetpack – Seen when he follows Anakin into battle with the droids The Clone Wars movie NOTE: Standard Jango Fett color scheme is NOT acceptable.   Report Content Issue: * Blank Page Invalid Contents Broken Links Other Your Name: * Details: * Submit...

    read more

    Captain Rex, Phase 1

    Captain Rex, Phase 1

    CHARACTER DESCRIPTION CT-7567, nicknamed “Rex,” was a clone trooper captain during the Clone Wars, the galaxy-wide conflict between the Galactic Republic and the Confederacy of Independent Systems. Rex was in command of Torrent Company, a unit of the famed 501st Legion in the Grand Army of the Republic. Rex served under Jedi General Anakin Skywalker, and was a freethinking, tough, and aggressive trooper. Though loyal and committed to his duty and to his fellow clones, Rex proved capable of questioning his superiors and, under extreme circumstances, outright disobeying orders if he believed them to be wrong. Rex displayed a strong working relationship and a degree of friendship with Commander Cody. Rex was one of the many clones of bounty hunter Jango Fett, bred on Kamino by the Galactic Republic to fight in the Republic’s clone army. The soldiers were bred to fight against the separatist planetary and sectorial governments seeking to leave the Republic, known as Confederacy of Independent Systems, in the coming war. Rex served on Geonosis alongside Denal and was promoted to the rank of captain, he was also in command of Torrent Company, a unit in the famous 501st Legion. Rex was assigned to Jedi General Anakin Skywalker, and would participate in many missions alongside the Jedi Knight, including Jabiim. Rex also developed a friendship with fellow clone trooper Commander Cody. Source: Wookiepedia REQUIRED ITEMS 1. Black Undersuit One or two piece black undersuit. Commonly used components include sports compression wear, warm-up suits, dance unitards, or diveskins. Undersuit must be smooth in appearance or with vertical ribbing with no labels or logos visible once the armor is on. 2. Black Gloves Black over the wrist gloves made of leather, nylon, or other low pile fabrics. Gloves must not show any labels or logos once the armor is on and cover any exposed skin. 3. Neck Seal Neck seal to be black in color with vertical ribbing or being smooth in appearance. No logos or labels are to be visible. If the seal is not incorporated as part of the undersuit, a balaclava or other similar covering is acceptable. 4. Helmet The Clone Wars animated style clone helmet – Fanmade helmet. Visor – Black visor covers entire “T” shape and frown Helmet Fin on dome 4 black vents on each side of helmet Blue jaig eyes on forehead Blue visor trim and rear detail Yellow “kill stripes”, 4 on each side of the forehead Rangefinder (animated style) mounted on right/outside of helmet Smoked/black visor over entire opening on face of helmet NOTE: Episode II style helmets are not acceptable 5. Armor Chest and back plate should match together at the sides with no gap, just a seam line. Shoulders – Blue stripes centered on shoulders Shoulder Straps – Correct shape with ridges. Upper Arms – Front/back pieces are seamless. Blue stripes on outside of biceps Forearms – Front/back pieces are seamless. Blue stripes on elbows and forearms Handplates AB plate Kidney/Lower Back Piece Butt Plate Cod piece Upper thighs – Front/back pieces are seamless. Lower Legs – Blue stripes centered on knees Compad on left forearm 6. Clone Trooper boots White shoes with white soles Strap across top of foot with circular detail pieces at each end Proper toe detail No laces or logos 7. Belt The Clone Wars style belt Segmented (or segmented-look) belt One...

    read more